February
Monday 2 April 2018 photo 7/20
![Cisco route map configuration guide: >> http://wva.cloudz.pw/download?file=cisco+route+map+configuration+guide << (Download)
Cisco route map configuration guide: >> http://wva.cloudz.pw/read?file=cisco+route+map+configuration+guide << (Read Online)
Route Filtering and Route-Maps -. Prefix-Lists. Prefix-lists are used to match routes as opposed to traffic. Two things are matched: • The prefix (the network itself). • The prefix-length (the length of the subnet mask). Consider the following prefix-list: Router(config)# ip prefix-list MYLIST 10.1.1.0/24. The above prefix-list
Cisco ASA 5500 Series Configuration Guide using the CLI. 23. Defining Route Maps. This chapter describes route maps and includes the following sections: • Information About Route Maps, page 23-1. • Licensing Requirements for Route Maps, page 23-3. • Guidelines and Limitations, page 23-3. • Defining a Route Map,
QC-44. Cisco IOS Quality of Service Solutions Configuration Guide. To enable PBR on an interface, use the following commands beginning in global configuration mode: Command. Purpose. Step 1. Router(config)# route-map map-tag [permit | deny]. [sequence-number]. Defines a route map to control where packets are.
25 Jan 2018 To enable policy-based routing on an interface, indicate which route map the device should use by using the ip policy route-map map-tag command in interface configuration mode. A packet arriving on the specified interface is subject to policy-based routing except when its destination IP address is the
23 Mar 2010 This chapter helps you prepare for the CCNP ROUTE exam by covering the following topics related to implementing path control: Offset lists, Cisco IOS IP Service Level Agreements, and Policy routing using route maps.
26 Nov 2003 Using Figure 2-1 as a guide, Example 2-12 lists the route table of the clanton router followed by the route map configuration used to match the OSPF routes with a metric of 20. This example redistributes OSPF routes into EIGRP routes that have a metric of 20.
One or more match commands and one or more set commands typically follow a route-map global configuration command. If there are no match commands, then everything matches. If there are no set commands, nothing is done (other than the match). Therefore, you need
alliedtelesis.com. Feature Overview and Configuration Guide. Technical Guide. C613-22060-00 REV A. Introduction. This guide introduces route maps for filtering in BGP and OSPF. Route maps offer a complex combination of match criteria and actions. They can be used to filter BGP and OSPF routes, to alter the properties
Software Configuration Guide—Release 12.2(25)SG This chapter describes the tasks for configuring policy-based routing (PBR) on a router and includes . Command. Purpose. Step 1. Switch(config)# route-map map-tag [permit | deny] [sequence-number]. Defines a route map to control where packets are output. This.
Cisco IOS Software Configuration Guide, Release 15.0SY. Chapter 1 Policy-Based Routing (PBR). How to Configure PBR. Configuring PBR. To configure PBR on an interface, use the following commands beginning in global configuration mode: Command. Purpose. Step 1. Router(config)# route-map map-tag [permit](http://cdn08.dayviews.com/501/_u4/_u1/_u2/_u8/_u6/_u2/u4128627/60479_1522651804/Cisco_route_map_configuration_guide_http_wva_cloudz_pw_download_file_cisco_route_map_configuration.jpg)
|
Cisco route map configuration guide: >> http://wva.cloudz.pw/download?file=cisco+route+map+configuration+guide << (Download)
Cisco route map configuration guide: >> http://wva.cloudz.pw/read?file=cisco+route+map+configuration+guide << (Read Online)
Route Filtering and Route-Maps -. Prefix-Lists. Prefix-lists are used to match routes as opposed to traffic. Two things are matched: • The prefix (the network itself). • The prefix-length (the length of the subnet mask). Consider the following prefix-list: Router(config)# ip prefix-list MYLIST 10.1.1.0/24. The above prefix-list
Cisco ASA 5500 Series Configuration Guide using the CLI. 23. Defining Route Maps. This chapter describes route maps and includes the following sections: • Information About Route Maps, page 23-1. • Licensing Requirements for Route Maps, page 23-3. • Guidelines and Limitations, page 23-3. • Defining a Route Map,
QC-44. Cisco IOS Quality of Service Solutions Configuration Guide. To enable PBR on an interface, use the following commands beginning in global configuration mode: Command. Purpose. Step 1. Router(config)# route-map map-tag [permit | deny]. [sequence-number]. Defines a route map to control where packets are.
25 Jan 2018 To enable policy-based routing on an interface, indicate which route map the device should use by using the ip policy route-map map-tag command in interface configuration mode. A packet arriving on the specified interface is subject to policy-based routing except when its destination IP address is the
23 Mar 2010 This chapter helps you prepare for the CCNP ROUTE exam by covering the following topics related to implementing path control: Offset lists, Cisco IOS IP Service Level Agreements, and Policy routing using route maps.
26 Nov 2003 Using Figure 2-1 as a guide, Example 2-12 lists the route table of the clanton router followed by the route map configuration used to match the OSPF routes with a metric of 20. This example redistributes OSPF routes into EIGRP routes that have a metric of 20.
One or more match commands and one or more set commands typically follow a route-map global configuration command. If there are no match commands, then everything matches. If there are no set commands, nothing is done (other than the match). Therefore, you need
alliedtelesis.com. Feature Overview and Configuration Guide. Technical Guide. C613-22060-00 REV A. Introduction. This guide introduces route maps for filtering in BGP and OSPF. Route maps offer a complex combination of match criteria and actions. They can be used to filter BGP and OSPF routes, to alter the properties
Software Configuration Guide—Release 12.2(25)SG This chapter describes the tasks for configuring policy-based routing (PBR) on a router and includes . Command. Purpose. Step 1. Switch(config)# route-map map-tag [permit | deny] [sequence-number]. Defines a route map to control where packets are output. This.
Cisco IOS Software Configuration Guide, Release 15.0SY. Chapter 1 Policy-Based Routing (PBR). How to Configure PBR. Configuring PBR. To configure PBR on an interface, use the following commands beginning in global configuration mode: Command. Purpose. Step 1. Router(config)# route-map map-tag [permit
Annons
Visa toppen
Show footer