Tuesday 11 September 2018 photo 8/14
|
Mtk6575 scatter file
※ Download: http://relenchuna.moidnityt.ru/?dl&keyword=mtk6575+scatter+file&charset=utf-8&source=dayviews.com2
Программа отключить антивирус 6. Как подключать, с батареей или без с какими зажатыми кнопками определяете сами, методом перебора. Пробовал пару прошивок с сайтов вышеупомянутых. I just don't know if this works to Rio but I guess it's best to follow your route.
Step 2 : Extract to your computer. Отключил от компа,заново подключаю-не видит комп вобще ничего,пишет не подключено через порт юсб и всё. Установка recovery для смартфонов на Android, на процессоре MTK Кастомные прошивки, как правило, устанавливаются через recovery это такое меню для востановления системы, в него можно попасть при загрузке.
MENU - Its therefore important that you not mistake scatter file for stock rom or firmware.
Hey, I have been years just reading these forums but never made any posts, so thats why I cannot post to development section anyways. I happened to totally brick my phone by flashing wrong preloader into it. However this morning i succesfully reflashed it and now I have somehow working phone just need to find new rom now but anyways. This thread is to help other people who has semi bricked their phones as well. If your computer doesn't see your phone at all make modified USB connect the 4pin to ground. This is what I did actually. If that doesn't work you can google for test points. Install windows XP Yes, windows 8 didn't work for me. I will not write steps how to install windows xp Install USB deview -Google it, download it, extract package and run it -Remove all drivers related to Mediatek, android, usb vcom etc. Download and install VCOM USB Drivers -Download these drivers -Put your phone battery in 50% charge required. Now you have to wait in device manager connect the phone right click the device when it shows up. After windows have found drivers UNTICK show compatible devices. And MANUALLY select preloader driver. Now it will install it the next time the device connects. OK now we have Preloader driver in place. Notice that we will install one more driver later needed in flashing procedure. Now download compatible rom. Ok lets recap what we have now: -preloader drivers -phone disconnected -SP Flash Tool v3. Next we need to flash compatible rom this part is tricky. Read before doing anything. If everything went fine you get yellow progress bar and it will reflash your phone! In the last part if you got Error 5054, This is good. It means your phone is still alive! So you need to go back to google and download other rom try flashing everything thats what I did, before hitting jack pot, eventually you will find compatible rom If you got ERROR 3002 switch back to SP Flash Tool v3. I got some other errors as well when flashing and I solved them but didn't write down the errors so I cant remember them sorry Remember before connect phone as META mode. Plug in battery with atlaest 50% power wait 15s. This was the mysterious step I was missing when struggling with this 5 days! By the time of writing this article I got my phone working rom, everything works. I happened to totally brick my phone by flashing wrong preloader into it. However this morning i succesfully reflashed it and now I have somehow working phone just need to find new rom now but anyways. This thread is to help other people who has semi bricked their phones as well. If your computer doesn't see your phone at all make modified USB connect the 4pin to ground. This is what I did actually. If that doesn't work you can google for test points. Install windows XP Yes, windows 8 didn't work for me. I will not write steps how to install windows xp Install USB deview -Google it, download it, extract package and run it -Remove all drivers related to Mediatek, android, usb vcom etc. Download and install VCOM USB Drivers -Download these drivers -Put your phone battery in 50% charge required. Now you have to wait in device manager connect the phone right click the device when it shows up. After windows have found drivers UNTICK show compatible devices. And MANUALLY select preloader driver. Now it will install it the next time the device connects. OK now we have Preloader driver in place. Notice that we will install one more driver later needed in flashing procedure. Now download compatible rom. Ok lets recap what we have now: -preloader drivers -phone disconnected -SP Flash Tool v3. Next we need to flash compatible rom this part is tricky. Read before doing anything. If everything went fine you get yellow progress bar and it will reflash your phone! In the last part if you got Error 5054, This is good. It means your phone is still alive! So you need to go back to google and download other rom try flashing everything thats what I did, before hitting jack pot, eventually you will find compatible rom If you got ERROR 3002 switch back to SP Flash Tool v3. I got some other errors as well when flashing and I solved them but didn't write down the errors so I cant remember them sorry Remember before connect phone as META mode. Plug in battery with atlaest 50% power wait 15s. This was the mysterious step I was missing when struggling with this 5 days! By the time of writing this article I got my phone working rom, everything works. Screen : 540x960 BB Chip : MT6577 Ms Board : Glaxy S3 IMEI1 : XXXXXX IMEI2: XXXXXX Modem Ver. Because thşs rom very stable but one except, google contacts cant sync. And i m trying cwm install with MTKdroid tools its runing but ONLY ONE TAKE. After the reboot in CWM menu coming orginal factory recovery yellow simple screen and only have test etc.
Annons