Sunday 3 December 2017 photo 8/15
![]() ![]() ![]() |
Fleck 9100 control valve manual: >> http://ija.cloudz.pw/download?file=fleck+9100+control+valve+manual << (Download)
Fleck 9100 control valve manual: >> http://ija.cloudz.pw/read?file=fleck+9100+control+valve+manual << (Read Online)
fleck 9000 sxt manual
fleck 9500 spec sheet
fleck 9500 sxt manual
fleck 9500 parts
pentair 9500 manual
fleck 9100sxt programming
fleck 9100 parts
fleck 9100sxt manual
The Fleck service manual covers other types of systems as well such as water softeners and filters, so there may be information in your Fleck service manual that does not pertain to your system. Please review this start-up guide Fleck 9100 backwash control valve & bypass valve. 1. Pipe connector kit (either 1"or ?"). 1.
This document is available in other languages on www.pentairaquaeurope.com/product-finder/ product-type/control-valves. 1.2. Release management. 1.3. Manufacturer identifier, product. Manufacturer: Pentair Manufacturing Italy Srl. Via Masaccio, 13. 56010 Lugnano di Vicopisano (PI) – Italy. Product: Fleck 9100 - SXT.
4 • FLECK® 9000/9100/9500 Service Manual. 19210 Rev D. Figure 5 Program Wheel. 19. Cycle timer into backwash position. Turn manual knob so that the micro switch rides on the first set of pins. In this position the tanks switch (lower piston) and the control valve moves to the backwash position (upper piston). Wait.
9000/9100/9500 Duplex Watersoftener. Installation Operation Maintenance Manual. 9xDXIOMMpage 3. NOS. PAGE. 7.0. ASSEMBLY/INSTALLATION. 14. 7.1. Mechanical. 14. 7.1.1 Assembling Vessel, Riser Tube and Internals. 14. 7.1.2 Charging the Resin. 14. 7.1.4 Assembling the Control Valve. 15. 7.1.5 Attatching the
Applied Membranes, Inc. Manufacturer & distributor of Reverse Osmosis RO Systems, Membranes and Components. An ISO 9001:2008 Certified Company.
Installing the Fleck 9100SXT Meter Control Valve: • Using the included silicone lubricant packet, lubricate the inner and outer o- rings on the bottom of the Fleck 9100SXT Meter Valve as shown in Figures 5. & 6 below. Please repeat this for the main valve, and the secondary portion, as shown below. FIGURE 5. FIGURE 6.
Fleck Model 9000/9100/9500. Service Manual. 40944 Rev E . 9000/9100/9500 INJECTOR FLOW DATA. (1600 SERIES . Turn manual knob so that the micro switch rides on the first set of pins. In this position the tanks switch (lower piston) and the control valve moves to the backwash position (upper piston). Wait until the
Dow Corning® 7 Release Compound is used in the manufacture of Fleck® control valves. Rotate the valve clockwise from zero. 3. LOCATION OF SOFTENER AND DRAIN: The softener should be located close to a drain. Petroleum-based lubricants can cause swelling in rubber parts. ELECTRICAL FACILITIES: A
Model 9000/9100/9500. 7. 16. Cycle timer into backwash position. Turn manual knob so that the micro switch rides on the first set of pins. — In this position the tanks switch (lower piston) and the control valve moves to the backwash position (upper piston). — Wait until the positioning of upper and lower pistons stops before
9100SXT Valve. Meter Initiated Water Softener. Operation Manual. #54745 2/09. Read all instructions carefully before operation. The control will only enter the Program Mode with the valve in Service. If power fails while the unit is in regeneration, the control will save the current valve position before it shuts down. When.
Annons