Wednesday 19 September 2018 photo 9/22
![]() ![]() ![]() |
Xerox workcentre 3550 file exists or the failure is unspecified
※ Download: http://terchimaton.teddyvasya.ru/?dl&keyword=xerox+workcentre+3550+file+exists+or+the+failure+is+unspecified&charset=utf-8&source=dayviews.com2
I'm relatively new to GPO's so any help would be greatly appreciated. Однако настроить никак не получается.
He was unable to scan to the network server. Now, I have a new iMac running Mavericks.
#title - The service manual is the document used as theprimary information source for repairing and maintaining this family of products and isavailable as EDOC on a CD-ROM, or as a bookmarked PDF on CD-ROM. I have check the user guide top to bottom and i cannot seem to find where to configure this.
Switch off the machine, then switch on the machine. Enter dC330 code 10-100 to heat the fuser to 180 degrees. Enter codes 10-200 to verify the condition of the thermistor. Switch off the machine. Remove the fuser assembly. Check that the thermistor is clean and in good contact with the fuser heat roll. Check the wiring to the thermistors. Install new components as necessary. Check for continuity between the two pins on the fuser assembly connector. Check that there is continuity through the fuser heater and across the over temperature cut-out. Check the wiring between the following connectors: a. The fuser connector and CON2 on the SMPS. The fuser connector and CN19 on the Main PWB. If necessary, install a new fuser connector. Perform OF7 Main PWB Check RAP. Although the fuser unit can return to a normal operating temperature, the fuser may consequently be damaged. Enter code dC330 code 10-200. Perform a fuser temperature check to verify the condition of the thermistors. Switch off the machine. Remove the fuser assembly. Examine the fuser assembly for heat damage. Install new components as necessary. Check that the thermistor , is clean and in good contact with the fuser. Check the wiring to the thermistor. Install a new thermistor as necessary. Check that there is continuity through the fuser heater and across the over temperature cut-out. If necessary, install a new thermostat assembly. Check the wiring between the following connectors: a. The fuser connector and CON2 on the SMPS. The fuser connector and CN19 on the Main PWB. If necessary, install a new fuser connector. Perform OF7 Main PWB Check RAP. No immediate action is necessary. Ensure that a replacement fuser assembly is in stock. Install a new fuser assembly. Check that the scanner lock is completely unlocked. Remove the scanner cover. Check that the CCD module moves freely from left to right. Check the wiring between the CCD home sensor and CN5 on the Main PWB. If necessary, install a new CCD home sensor. Check the wiring between the scan motor and CN4 on the Main PWB. Perform OF7 Main PWB Check RAP. The faults are listed in code order, together with any recommended action. Please note that service actions are limited. The SMTP server authentication may be supported but not enabled on the device or any 500 code is returned from the mail server. Re-enter the email address. This can occur when the machine is configured to send a maximum mail size. Increase the mail size via CentreWare Internet Services. If the fault persists, increase the mail size allocation on the mail server. Confirm that the group is available and has mail addresses associated with it. Error returned by NIC during SMTP encoding activity. Error returned by NIC for memory failure during SMTP operation. Miscellaneous error returned by NIC during SMTP operation. Switch off the machine, then switch on the machine. Check the network connection. Switch off the machine, then switch on the machine. Enter a valid user name and password. Check the SMTP IP address or host name. Check that the SMTP port is open and working correctly. Check that the DNS server is online. Reduce the mail size option. Check the LDAP IP address or host name. Check that the LDAP port is correct and open. The LDAP server authentication may be supported but not enabled on the device or the maximum search results have been exceeded. Check the spelling of the LDAP entry, then resend the email. Check the scanner, refer to the 14-100 CCD Lock RAP. Refer to the System Administration Guide. Check the DNS server setup or enter a valid email address. Enter a valid email address. Check the POP3 server setup. Re-enter the user name and password. Refer to the System Administration Guide. Final Actions Perform the OF7 Main PWB Check RAP. The faults are listed in code order, together with any recommended actions. Please note that the service actions are limited. The upper LED on indicates that the PWB is ready. The lower LED flashing indicates that the network is good. Go to GP 4 System Administration Tools. Check with the customer that the connectivity and network setup settings are correct. Check with the customer that the connectivity and network setup settings are correct. Refer to GP 4 System Administration Tools. Check with the customer that the connectivity and network setup settings are correct. Refer to GP 4 System Administration Tools. Check with the customer that the connectivity and network setup settings are correct. Refer to GP 4 System Administration Tools. Check with the customer that the connectivity and network setup settings are correct. Refer to GP 4 System Administration Tools. Check the network cable. Shorten the file name. Change the file name. Go to GP 4 System Administration Tools. Select Connectivity and Network Setup. Switch off, then switch on the machine. If the fault persists, again disable dynamic addressing. Assign a new static IP address.
Annons